150Ah 12V Lithium Ion Battery for Inverter

Item No.: TWE0299
Nominal Voltage: 12.8V
Nominal Capacity: 150Ah
Energy: 1920Wh
Max Dimensions: 485x170x240mm
Certificate: CE, ROHS, UN38.3, IEC62133, etc.
Weight: 18kg
Warranty: 2 years
Description Brand Introduction Review
Description

Product Overview

This 150Ah lithium battery stores 1920Wh in one sealed case at 12.8V nominal. The cells inside are LiFePO4, a chemistry that holds its voltage under load and tolerates sitting at full charge far better than cobalt-based lithium cells, which is why it dominates stationary and vehicle auxiliary duty. Against the lead-acid block it usually replaces in a solar battery bank, the weight difference is the first thing an installer notices: roughly 70% lighter for the same nominal capacity, with no electrolyte to check, no watering schedule and no venting to plan for. Real numbers move with the installation — a rechargeable lithium battery held at full charge in a hot cabinet ages faster than one cycled at moderate depth with air around it. In a system it sits between the charger and the inverter or DC load, and sizing starts from the load: work out the watt-hours the load needs, allow for inverter losses, and the 150Ah capacity sets how long the system runs before the pack reaches its cut-off.

A residential house with dark solar panels mounted across a tiled roof
Solar street light installed along a road
Shenzhen BST Technology Co

Battery Management & Protection

Several protections, one board. The smart BMS inside the case tracks cell-group voltage, pack current and temperature, and opens the charge or discharge path when any of them leaves its safe band. Over-charge, over-discharge, over-current, over-voltage, short circuit, cell protection and temperature protection are all handled at pack level.

Large industrial printing or packaging machine line in a cleanroom

Cell-level, not terminal-level. Because it watches individual cell groups rather than the two case terminals, the BMS catches an imbalance long before the whole pack voltage looks low — the failure mode that quietly kills packs built without cell monitoring.

150Ah 12V Lithium Ion Battery for Inverter

Current and short circuit. A stalled motor, a reversed connection or a dead short on the DC feed of a battery pack for inverter duty trips the pack instead of cooking the cable, and the pack returns to service once the fault is removed.

150Ah 12V Lithium Ion Battery for Inverter

Temperature. Charging is inhibited outside the pack's charge window and discharge is limited at the extremes, which is what lets this lithium ion battery work in a cold vehicle bay or a warm cabinet without damage to the cells.

150Ah 12V Lithium Ion Battery for Inverter

Chemistry. A deep cycle lithium battery built on lithium iron phosphate is a thermally forgiving choice: no cobalt in the cathode, a more stable structure under abuse and far less of the thermal-runaway risk that makes other lithium chemistries a fire-service concern. It still deserves respect — keep it out of flame, never crush or pierce the case, and do not charge it below freezing.

150Ah 12V Lithium Ion Battery for Inverter

Where it stops. The BMS protects the cells, not the installation: cable sizing, fusing and charger settings sit outside it and still have to be right. A 12V lithium battery that trips repeatedly is usually telling you the system around it is undersized, not that the battery is faulty.

Large black PA speaker shown during an outdoor live music performance
Anbotek RoHS conformity certificate for a lithium ion battery
IECEE CB test certificate for a lithium-ion polymer battery

Quality & Certification Records

ItemDetail
Safety certificationCE, CB, IEC62133, UL, PSE
Environmental complianceRoHS, REACH
Quality managementISO 9001, ISO 14001, BSCI
Factory auditSGS and Intertek
Cell screeningevery cell cycled 3 times before assembly
Final inspection100% check of appearance, voltage, capacity, resistance and dimensions
EU conformityDirective 2011/65/EU and Delegated Directive (EU) 2015/863
RoHS test basisIEC 62321 series methods
ISO 9001 quality management system certificate for a lithium ion battery manufacturer
EU EMC certificate of conformity for a lithium ion battery
Industrial stainless-steel mixing equipment in a cleanroom

Charge & Discharge Performance

  • Continuous output: 75A continuous discharge at 12.8V nominal is about 960W going into the inverter, so a 1kW inverter with normal derating sits comfortably inside the rating of a battery pack for inverter duty.
  • Surge headroom: the pack delivers 150A for up to 5 seconds, which covers inverter start-up, motor inrush on a golf cart or the compressor kick on a fridge — the few seconds where a smaller pack would trip its protection.
  • Voltage hold under load: In solar energy storage battery service, a lithium iron phosphate battery keeps its terminal voltage higher than a lead-acid block of the same nominal capacity as it empties, so an inverter is less likely to trip on low input while there is still usable energy left.
  • Rated capacity point: capacity is quoted at 0.2C, a 30A discharge, which is the reference rate for a 12V lithium battery of this size. Pull harder and you get slightly less energy out, exactly as the data sheet implies.
  • Recharge time: at the 30A standard charge current a flat pack is back to full in roughly five hours. As with any deep cycle lithium battery the final stretch is constant-voltage, so the last part of the curve takes longer than the middle.
  • Faster turnaround: the 75A maximum charge current brings a full charge down to a little over two hours, provided the charger, breaker and cabling are rated for it and the pack is inside its charge temperature window.
  • Runtime planning: a full 150Ah lithium battery runs about 4 hours at a 400W load and around 1.5 hours at 1kW once inverter losses are taken out. Use that as a sizing guide, then confirm against your own measured load profile.
Control console and yellow roller of an industrial machineClose-up of industrial machinery with metal rollers and tubesFactory worker standing in front of large stainless steel production machines in a cleanroomWorker in a white suit operating an automated production line inside a glass enclosure
150Ah 12V Lithium Ion Battery for Inverter
White motorhome with scenic side graphics parked in mountains
White golf cart with brown seats and a golf bag

Mounting & Commissioning

  1. Plan the space before you lift anything: the terminal posts on this 12V lithium battery sit on the top face, so budget clearance above them for lugs and cable bend, and keep the case away from sharp edges and heat sources.
  2. Lift this 150Ah lithium battery by its moulded side handles, never by the posts, and use a second pair of hands if the tray is awkward to reach.
  3. Strap or bracket the battery pack for inverter or vehicle mounting down so it cannot slide. The shell is ABS, so spread the clamping load with a plate or a wide strap rather than tightening a narrow bracket into the side.
  4. Land the cables on the M8 posts with ring lugs sized for the conductor: positive lead first, negative lead last, torque to the lug maker's figure, and support the cable so the post carries no strain.
  5. Fit a fuse or breaker on the positive feed close to the lithium battery pack, rated for the cable rather than for the pack's maximum output, so a short anywhere in the run clears before the cable overheats.
  6. Set the charger to a LiFePO4 battery profile using the cut-off voltage in the specification table above, then run a full charge and check that it terminates cleanly at that point.
  7. Set the inverter's low-voltage cutoff to the recommended discharge value and watch the first full cycle: terminal voltage should climb smoothly, nothing should run hot, and the BMS should stay closed throughout.
A cleanroom manufacturing floor with workers in blue uniforms and production machinery
A close-up of industrial production equipment with blue platforms and mechanical components
150Ah 12V Lithium Ion Battery for Inverter

Applications

  • Solar storage and off-grid systems: the pack holds daytime charging for evening loads, and a solar energy storage battery bank assembled from 12V blocks is the usual layout at this capacity.
  • Solar street lights, billboard lighting and emergency lighting: lighting controllers expect a steady 12V, and the flat discharge curve keeps lamp output consistent until the BMS cuts off rather than dimming for the last hour.
  • Backup power, UPS and telecom sites: when mains drops, the lithium battery pack takes the load without the voltage sag a lead-acid string shows under the same transfer, so connected equipment sees a cleaner switchover.
  • Golf carts, RVs, AGVs and forklifts: a deep cycle lithium battery of this size is the usual upgrade from a lead-acid traction or house bank — the weight comes off, run time goes up and there is no watering between trips.
  • Electric scooters and small EVs: a lithium ion battery at traction voltage normally drives the motor, while a 12V block like this one runs lights, controllers and accessory circuits through a DC-DC converter.
  • Security and access control, electric sprayers, fish finders and garden tools: small devices built around a sealed lead-acid brick are the most common lithium battery replacement request at this capacity, because the terminals, voltage and footprint carry over with far less weight.
  • Portable audio and home appliances: PA speakers, coolers and 12V household devices run longer on the same footprint, and the pack can be sited in any compartment that stays dry.
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter

Specifications

ItemSpecification
Model No.TWE-LF12V150AH
Nominal Voltage12.8V
Nominal Capacity150Ah (standard discharge at 0.2C after a standard charge)
Dimensions485 x 170 x 240 mm (L x W x H)
WeightApprox. 18 kg
Cycle Life2000 cycles or more to 80% of the initial capacity
Internal Resistance≤25 mΩ
Housing MaterialABS, IP65
Terminal TypeM8
Voltage WindowCharge cut-off 14.6V; discharge cut-off 9.2V (10V recommended)
Charge Current30A standard, 75A maximum
Discharge Current30A standard, 75A continuous, 150A pulse for up to 5s
Operation TemperatureCharge 0 °C to 45 °C; discharge −20 °C to 60 °C
Storage Temperature−20 °C to 25 °C for 12 months; −20 °C to 35 °C for 3 months; −20 °C to 45 °C for 1 month
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter

Ordering & Delivery

  1. Send the target specification. Tell us the system voltage, the load profile, the quantity and the destination. A custom lithium battery order is confirmed against that specification, because terminal arrangement, packing and documentation follow the application rather than a catalogue part number.
  2. Quotation and terms. The quotation sets price, order quantity and lead time for the configuration you ask for, and confirms payment terms and the delivery window in the same document.
  3. Documentation. Each shipment leaves with UN38.3, MSDS and the Air/Sea Transport Identification & Classification report, plus the certificates your market requires for a lithium iron phosphate battery. Tell us what your forwarder or customs broker needs before the pack is packed.
  4. Packing and shipping. Each lithium battery pack is packed for the transport mode and shipped by sea, air or express from Shenzhen, Shanghai or Hong Kong, whichever route your schedule and paperwork support.
  5. Warranty. This 12V pack carries a 2-year warranty, and our 51.2V stacked solar energy storage battery systems carry a 5-year warranty. Confirm in writing the cover that applies to your order and how a claim would be handled.
  6. Validation before release. If the pack has to work inside an existing enclosure or with a particular inverter, ask your sales contact about sample availability and check the low-voltage behaviour on a test rig before the production order is released.
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter

Scale & Supply Capability

Topwell Power is a lithium battery manufacturer, not a trading house. Our range runs from compact packs to large storage systems, so buyers can consolidate several lines behind one specification standard and one set of shipping documents. OEM and private-label work is routine: your label, case marking, terminal choice, capacity and packing configuration. Capacities and enclosures are customised per project, samples are available before a production run, and shipments go out with the transport documentation freight forwarders ask for. Send your target specification and volume, and we will confirm lead time, packing and pricing for that order.

150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter
150Ah 12V Lithium Ion Battery for Inverter

FAQ

Can I charge this pack with my existing lead-acid charger?

Only if the charger can be set to a lithium profile that stops at the cut-off voltage shown in the specification table. Switch off equalise, desulphation and temperature compensation, because those modes are built for flooded lead-acid and will overwork a LiFePO4 battery. A fixed charger with no lithium setting is better replaced, or paired with a DC-DC charger designed for lithium.

Can I connect two or more packs in series or in parallel?

It can be done, but the arrangement has to match the BMS and your target system voltage, so send us the configuration before you wire it. Packs used together should be at the same state of charge and from the same production batch, and each string should carry its own fuse. A 12V lithium ion battery bank is not a matter of adding blocks until the voltage looks right.

What happens if the pack is left flat for months?

Recharge it as soon as you can. The BMS stops discharge before the cells are damaged, but a pack that has rested at low voltage for a long time may need a slow, low-current charge to come back, and a rechargeable lithium battery left flat for a year may not recover full capacity. For storage, leave it partway charged rather than full and top it up every few months.

What routine checks does the pack need?

Very little. Keep the top of the case clean and dry, check the terminal torque once a year, and read the terminal voltage when the pack comes out of storage. A healthy unit sits quietly between those checks.

Is the IP65 case suitable for outdoor mounting?

IP65 covers dust ingress and water jets, which suits a battery compartment, an outdoor cabinet or a lighting column, but it is not a submersible rating. Mount it where water cannot stand around the case, shield the terminals and keep direct sun off the shell — on a solar battery installation that is usually the difference between a pack that lasts and one that does not.

Can this pack be built to a different specification?

Within the 12V format, yes: terminal arrangement, case marking and packing can be set for a project, and a custom lithium battery build is confirmed against your drawing or sample before production starts. A different capacity moves you to another model rather than a modification of this one.

Brand Introduction

Yichun Topwell Power Co., Ltd (Trademark:TWE) established in 2002, is a high-tech enterprise focusing on the R&D, production and sales of lithium polymer batteries, lithium ion batteries, lithium iron phosphate batteries, and lithium thionyl chloride batteries. Products are widely used in consumer electronics, Internet of Things, smart home, medical, vehicle, home and outdoor energy storage, and have obtained CE, RoHS, Reach, UN38.3, IEC62133, CB, UL, MSDS certifications, etc.

 

Topwell moves on by providing reliable, efficient and intelligent battery solutions to meet different energy needs. We have efficient engineering, production and quality management teams. From raw material procurement, to production, testing, sales and after-sales service, all steps have been controlled by a strict quality management system. Our factory has passed ISO9001, IS014001, BISI certification, SGS, Intertek audit. With the advantages in price, quality and service, we have established long-term and stable cooperative relationships with many well-known brands. Topwell always attached the great importance to the long term cooperation with customers. No matter the order is big or small, we do our best to support you the highest quality with favorable price. We believe that Topwell Power can be your best battery supplier!

Review
Review

ver_code
1/3
X
Send your message to us
ver_code